CANOPEN优点及参考例程
为什么选用CANopen？
可支持多轴
CANopen最多支持控制127个轴，且通讯速率可高达1Mbps。
CANopen总线对数据通信数据块进行编码的方式，可以多主方式（Multi-master）, 采用可靠的错误处理和检错机制，其协议包含了系统的，专业的工业用设备子协议，是专门为工业控制而发展的总线协议。符合工业控制所要求的高速，稳定可靠，高实时性要求
布线简单
用传统脉冲方向或模拟量来驱动一个直角坐标机构至少需要连接4根线或者更多，CANopen方案布线简单，所有轴并联接入CAN_H和CAN_L信号即可。减少布线，更少出错，减少布线成本，人工成本，后期电缆老化或故障的维护成本，以及由于复杂的线路故障带来的不可估量的损失。
如下一些参考例程，供参考
**** 电机使能 – CiA 402协议下 ****
$0603 $8 $2B $40 $60 $00 $06 $00 $00 $00 ‘Ready to Switch on
$0603 $8 $2B $40 $60 $00 $07 $00 $00 $00 ‘Switched on
$0603 $8 $2B $40 $60 $00 $0F $00 $00 $00 ‘Operation Enabled
**** 设置到位置表模式 ****
$0603 $8 $2F $60 $60 $00 $01 $00 $00 $00 ‘Set to Profile Position Mode
**** 设置运动参数 ****
$0603 $8 $23 $81 $60 $00 $F0 $00 $00 $00 ‘Set Profile Velocity to 1 rps
$0603 $8 $23 $83 $60 $00 $58 $02 $00 $00 ‘Set Acceleration to 100 rps/s
$0603 $8 $23 $84 $60 $00 $58 $02 $00 $00 ‘Set Deceleration to 100 rps/s
点对点绝对运动
$0603 $8 $23 $7A $60 $00 $40 $0D $03 $00 ‘Set Target Position to 200000 steps
$0603 $8 $2B $40 $60 $00 $1F $00 $00 $00 ‘Set New Set Point Bit to 1
$0603 $8 $2B $40 $60 $00 $0F $00 $00 $00 ‘Clear New Set Point Bit
点对点相对运动
$0603 $8 $23 $7A $60 $00 $40 $0D $03 $00 ‘Set Target Position to 200000 steps
$0603 $8 $2B $40 $60 $00 $5F $00 $00 $00 ‘Set New Set Point Bit to 1
$0603 $8 $2B $40 $60 $00 $4F $00 $00 $00 ‘Clear New Set Point Bit
多点运动，点与点间有停止动作
$0603 $8 $23 $81 $60 $00 $B0 $04 $00 $00 ‘Set Profile Velocity to 5 rps
$0603 $8 $23 $7A $60 $00 $40 $0D $03 $00 ‘Set Target Position to 200000 steps
$0603 $8 $2B $40 $60 $00 $5F $00 $00 $00 ‘Set New Set Point Bit to 1
$0603 $8 $2B $40 $60 $00 $4F $00 $00 $00 ‘Clear New Set Point Bit
$0603 $8 $23 $81 $60 $00 $60 $09 $00 $00 ‘Set Profile Velocity to 10 rps
$0603 $8 $23 $7A $60 $00 $40 $0D $03 $00 ‘Set Target Position to 600000 steps
$0603 $8 $2B $40 $60 $00 $5F $00 $00 $00 ‘Set New Set Point Bit to 1
$0603 $8 $2B $40 $60 $00 $4F $00 $00 $00 ‘Clear New Set Point Bit
多点运动，持续动作
$0603 $8 $23 $81 $60 $00 $B0 $04 $00 $00 ‘Set Profile Velocity to 5 rps
$0603 $8 $23 $7A $60 $00 $40 $0D $03 $00 ‘Set Target Position to 200000 steps
$0603 $8 $2B $40 $60 $00 $5F $02 $00 $00 ‘Set New Set Point Bit to 1
$0603 $8 $2B $40 $60 $00 $4F $02 $00 $00 ‘Clear New Set Point Bit
$0603 $8 $23 $81 $60 $00 $60 $09 $00 $00 ‘Set Profile Velocity to 10 rps
$0603 $8 $23 $7A $60 $00 $40 $0D $03 $00 ‘Set Target Position to 600000 steps
$0603 $8 $2B $40 $60 $00 $5F $02 $00 $00 ‘Set New Set Point Bit to 1
$0603 $8 $2B $40 $60 $00 $4F $02 $00 $00 ‘Clear New Set Point Bit
多点运动，动作间有条件变化
$0603 $8 $23 $81 $60 $00 $B0 $04 $00 $00 ‘Set Profile Velocity to 5 rps
$0603 $8 $23 $7A $60 $00 $40 $0D $03 $00 ‘Set Target Position to 200000 steps
$0603 $8 $2B $40 $60 $00 $7F $02 $00 $00 ‘Set New Set Point Bit to 1
$0603 $8 $2B $40 $60 $00 $6F $02 $00 $00 ‘Clear New Set Point Bit
$0603 $8 $23 $81 $60 $00 $60 $09 $00 $00 ‘Set Profile Velocity to 10 rps
$0603 $8 $23 $7A $60 $00 $40 $0D $03 $00 ‘Set Target Position to 600000 steps
$0603 $8 $2B $40 $60 $00 $7F $02 $00 $00 ‘Set New Set Point Bit to 1
$0603 $8 $2B $40 $60 $00 $6F $02 $00 $00 ‘Clear New Set Point Bit
**** 电机使能 – CiA 402协议下 ****
$0603 $8 $2B $40 $60 $00 $06 $00 $00 $00 ‘Ready to Switch on
$0603 $8 $2B $40 $60 $00 $07 $00 $00 $00 ‘Switched on
$0603 $8 $2B $40 $60 $00 $0F $01 $00 $00 ‘Operation Enabled; Motion Halted
**** 设置到速度表模式 ****
$0603 $8 $2F $60 $60 $00 $03 $00 $00 $00 ‘Set to Profile Velocity Mode
**** 设置运动参数 ****
$0603 $8 $23 $FF $60 $00 $F0 $00 $00 $00 ‘Set Target Velocity to 1 rps
$0603 $8 $23 $83 $60 $00 $58 $02 $00 $00 ‘Set Acceleration to 100 rps/s
$0603 $8 $23 $84 $60 $00 $58 $02 $00 $00 ‘Set Deceleration to 100 rps/s
**** 开始/停止 动作 ****
$0603 $8 $2B $40 $60 $00 $0F $00 $00 $00 ‘Motion Starts
$0603 $8 $23 $FF $60 $00 $60 $09 $00 $00 ‘Change Target Velocity to 10 rps
$0603 $8 $2B $40 $60 $00 $0F $01 $00 $00 ‘Motion Halts
**** 电机使能 – CiA 402协议下 ****
$0603 $8 $2B $40 $60 $00 $06 $00 $00 $00 ‘Ready to Switch on
$0603 $8 $2B $40 $60 $00 $07 $00 $00 $00 ‘Switched on
$0603 $8 $2B $40 $60 $00 $0F $00 $00 $00 ‘Operation Enabled
**** 设置到回原点模式 ****
$0603 $8 $2F $60 $60 $00 $06 $00 $00 $00 ‘Set to Homing Mode
$0603 $8 $2F $98 $60 $00 $13 $00 $00 $00 ‘Set Homing Method to 19
**** 设置运动参数 ****
$0603 $8 $23 $9A $60 $00 $58 $02 $00 $00 ‘Set Homing Acceleration to 100rps/s
$0603 $8 $23 $99 $60 $01 $F0 $00 $00 $00 ‘Set Homing Velocity (Search for Switch) to 1rps
$0603 $8 $23 $99 $60 $02 $78 $00 $00 $00 ‘Set Index Velocity (Search for Index or Zero) to 0.5rps
$0603 $8 $23 $7C $60 $00 $40 $9C $00 $00 ‘Set Homing Offset to 40000 Steps
$0603 $8 $2F $01 $70 $00 $03 $00 $00 $00 ‘Set Homing Switch to Input 3
**** 开始/停止 回原点 ****
$0603 $8 $2B $40 $60 $00 $1F $00 $00 $00 ‘Homing Starts
$0603 $8 $2B $40 $60 $00 $1F $01 $00 $00 ‘Homing Stops
**** 电机使能 – CiA 402协议下 ****
$0603 $8 $2B $40 $60 $00 $06 $00 $00 $00 ‘Ready to Switch on
$0603 $8 $2B $40 $60 $00 $07 $00 $00 $00 ‘Switched on
$0603 $8 $2B $40 $60 $00 $0F $00 $00 $00 ‘Operation Enabled
**** 设置到Q编程 ****
$0603 $8 $2F $60 $60 $00 $FF $00 $00 $00 ‘Set to Normal Q Mode
$0603 $8 $2F $07 $70 $00 $01 $00 $00 $00 ‘Set Q Segment Number to 1
**** 开始/停止 Q编程 ****
$0603 $8 $2B $40 $60 $00 $1F $00 $00 $00 ‘Q Program Starts
$0603 $8 $2B $40 $60 $00 $1F $01 $00 $00 ‘Q Program Halts
**** 电机使能 – CiA 402协议下 ****
$0603 $8 $2B $40 $60 $00 $06 $00 $00 $00 ‘Ready to Switch on
$0603 $8 $2B $40 $60 $00 $07 $00 $00 $00 ‘Switched on
$0603 $8 $2B $40 $60 $00 $0F $00 $00 $00 ‘Operation Enabled
**** 设置到同步Q程序 ****
$0603 $8 $2F $60 $60 $00 $FE $00 $00 $00 ‘Set to Sync Q Mode
$0603 $8 $2F $07 $70 $00 $01 $00 $00 $00 ‘Set Q Segment Number to 1
$0603 $8 $23 $05 $10 $00 $80 $00 $00 $00 ‘Set Sync Pulse to 0x80
**** 开始/停止 Q编程 ****
$80 $0 ‘Q Program Starts
$0603 $8 $2B $40 $60 $00 $0F $01 $00 $00 ‘Q Program Halts
**** 映射TPDO2 ****
$0000 $2 $80 $03 ‘Return back to “PreOperation” Mode
$0603 $8 $23 $01 $18 $01 $80 $02 $00 $80 ‘Turn off the TPDO2
$0603 $8 $2F $01 $1A $00 $00 $00 $00 $00 ‘Set Number of Mapped objects to zero
$0603 $8 $23 $01 $1A $01 $10 $00 $41 $61 ‘Map object1(0x6041) to TPDO2 subindex1.
$0603 $8 $23 $01 $1A $02 $20 $00 $0A $70 ‘Map object2(0x700A) to TPDO2 subindex2.
$0603 $8 $2F $01 $1A $00 $02 $00 $00 $00 ‘Set Number of total Mapped objects to Two
$0603 $8 $23 $01 $18 $01 $80 $02 $00 $00 ‘Turn on the TPDO2